Shoes technological requirements

1, cutting process
1, when receiving the kind of shoes should be single and like to prepare materials in strict accordance with customers requirements.
2, pattern board of point, line, teeth missing and so should all draw a clear picture of the material in the painting and paper model should be consistent.
3, should pay attention to cut cut cut curves were smooth, without gaps, and draw lines to cut.
4, prohibiting the use of ball-point pen when drawing materials, pens and so easy to wipe off the pen, there can not be altered during operation, and keep material cleanliness.
5, should pay attention to publishing accurate, materials and material direction, so as not to affect the results after molding. Layout should draw a large plate, then draw a small plate, saving material. air max tn
6, there are high frequency, electric embroidery parts, left and right direction to cut the more than 3-4. High frequency components must be cut foam.
7, cut a good material to use rubber bands tied up, placed in plastic bags, plastic bags on the target number, the customer, shoe last, size, etc., and then, and like one, kind of shoes together into the next process.
8, good self-test to ensure that the next process of semi-finished products into the mass. Second, sewing machine technology 1 day, clean the machine on time, maintain a good machine. 2, car-like one before you read the sample, check frequency, power and the kind of embroidery is a single line, to understand the structure and vehicles stood shoe law, look at board, a problem found in advance, to promptly resolve never to allow later resolved. 3, should be aligned with points, lines, car cover point line does not exceed 0.8 - 1mm. 4, including side to strong, fine, do not appear rough, loose and so on. 5, needle from 3 - 3.5 needles / cm, margins 1.2 - 1.5mm, spaced 2-2.0mm. 6, tongue and the rear car when the fabric edge in the shape of cars to follow the model, the phenomenon can not be deformed, white cloth to be increased in PE plastic protective film, and the routes to the same color and material. 7, vehicle belt fixed before the application of the torch 2 baking, avoid tearing the length of the wrong car to. 8, including sponge, the sponge should be protruding mouth around 5mm, around I do not pull too tight, to become full and firm, smooth curves, raising of foam and other materials when necessary, never allow the sponge under the swap. nike shoes 2010
9, ahead of Hong Kong Po affixed to run away from the edge 4mm, just press edges of second line. This phenomenon does not occur easily deformed head, after the Hong Kong Po affixed to 12mm away from the office to help foot, and after the Hong Kong Po catchy semi-circular edge to cut.
10 foot toe in cloth mesh openings to be patchwork. Patchwork pin 3.5 - 4 pin / mm.
11, PU, leather peeling rubber butt Department to wipe knocked flat, concave and convex phenomenon can not occur.
12 foot line along the edge network to help foot distance 2mm.
13, belly side of the case appears empty glue to rub together firmly.
14, anti-fur, PU cow to Pakistan a large area of piece reinforced slabs to avoid wrinkles.
15, encountered a shelter point, color, bad material, prohibited the use of unqualified high-frequency, embroidery and so eliminate the inflow of production.
16, car good help side to re-check again, clean thread, the same one, shoes together to manage. 17, to do well among the mutual inspection process to ensure product quality. 3, molding process 1, when the received samples uppers and soles and other materials, they shall arrange operation. 2, net laces to wear to the appropriate location: men's wear to a third, four-hole shoes prominently, children's shoes to wear to the third hole. nike air max ltd
3, to better match the number of shoe last, only after the confirmation required clearance on the line.
4, in contrast to release accurate, and can not appear before and after the dislocation distortion phenomenon.
5 days that the water to brush and white latex uniform, not too many days that water. Vehicles must follow the network of networks feet away from the feet of not exceeding 2.5mm, and the same color line.
6, tongue and laces should be added between the cardboard separated so as to avoid forming a shoelace after the tongue surface traces.
7, clamp to help clamp before the transfer by shoe last machine to help before they can work.
8, waist help to taut, high-end play followed with double.
Nine, drawing the bottom line before the first set of shoes to see whether covered by high-frequency, embroidery, if the cover should immediately take measures to draw lines when equipped with dual-level, the phenomenon can not appear distorted picture. Followed by a ribbon shoes, ribbon fixed to heel.
10, brush surface adhesive does not exceed the bottom line, gluing to the uniform, do not set glue, a lot of glue.
11, the end of glue brush not to spill when the glue, gluing uniform, pregnant with the first rubber soled shoes to gluing Lung treatment agent, to regulate the temperature.
12, affixed with double bottom should pay attention to, not distorted, pressure regulator before the end of a good machine, master of time and stress.
13, off lasts a good time to completely cool off before last, shoe last not to mix the sample to the production to go. nike air max 95
14, the entire shoe NOTE: A, excess glue; B, upper pollution; C, thread edges; D, degumming and other phenomena in order to solve; E, insole to put away the Serbian paper to be plugged when the first sheet of paper, so that can continue after the toe shape; F, wearing shoes with a direction should be careful to follow the reverse phenomenon can occur; G, should be placed in plastic bags after finishing, one both flat, not heap pressure. When you browse a variety of recreational sports shoe store, when you see a colorful variety of fashionable styles of the new shoes, when you are on a Li Ning, Nike or Adidas sneakers put it down, you whether or how to choose a new pair of shoes really belong to you but well-thought. We know that when your feet because the shoes bubble or not comfortable, because you do not really know how to choose their own shoes